Any specs on S2000 valve springs? I hear there might be a way to use them on K20A.org
Testing: Valvespring spring rates!
5
With this being a technical forum, we felt like it would be a good idea to show how to test valve spring pressure at both open and closed heights. Testing is a simple procedure but provides insight into a crucial and often overlooked component of the cylinder head.
The installed height of a valve spring is the length of the spring when it is installed on the head with the valves closed. It is important to differentiate between the advertised installed height and actual installed height. The most common advertised install height is 40.4mm or 1.5905 inches. This does not always translate into the actual installed height on a cylinder head. It can vary up and down based on a variety of factors including wear, manufacturing tolerances, and modification. These heights are measured by the spring only, so you have to factor in the thickness of the retainer as well as the spring base when it comes to setting your spring tester.
First you will need one of these:
![]()
A spring pressure tester is a simple tool. The spring is placed between the plates and the lever is used to compress the spring. The amount of forced exerted on the lower plate is shown on the scale needle.
Next, set the stop to the installed height of the valve spring. This limits the travel of the spring tester in order to provide an accurate measurement. A set of digital calipers is used to accurately set the stop at 40.4mm.
![]()
The next step is very simple. Place spring (with base and retainer) into the spring tester, and pull the lever. Be sure to take note of the pressure before moving onto the next spring.
![]()
The next step is to set the stop for the “open” position. In these tests we used an open lift of 0.520” The .520" lift number is just an arbitrary number we used for this example as many after market cams are around the .520 lift mark. Our KSi Cams are .535" lift.
![]()
Then place the spring assembly back into the tester and pull hard. Once again make sure you take note of the pressure.
![]()
Here is a list of some of the common valve springs people are using. Each of these measurements was done with the spring’s corresponding retainers and spring bases.
Supertech 1020D Valvesprings and Retainers kit
GO Power Dual Springs and Titanium Retainers kit
Skunk2 Pro Series Dual springs and Retainers
Eibach 20411.216 Dual Springs and Titanium Retainers
Stock 2006+ Civic Si Intake
Stock 2006+ Civic Si Exhaust
The Skunk2 and Eibach combos were tested in 2008. The GO Power and Supertech were re-tested last week.
If you would like, we can try and obtain and test other springs that people might be interested in.
The installed height of a valve spring is the length of the spring when it is installed on the head with the valves closed. It is important to differentiate between the advertised installed height and actual installed height. The most common advertised install height is 40.4mm or 1.5905 inches. This does not always translate into the actual installed height on a cylinder head. It can vary up and down based on a variety of factors including wear, manufacturing tolerances, and modification. These heights are measured by the spring only, so you have to factor in the thickness of the retainer as well as the spring base when it comes to setting your spring tester.
First you will need one of these:
A spring pressure tester is a simple tool. The spring is placed between the plates and the lever is used to compress the spring. The amount of forced exerted on the lower plate is shown on the scale needle.
Next, set the stop to the installed height of the valve spring. This limits the travel of the spring tester in order to provide an accurate measurement. A set of digital calipers is used to accurately set the stop at 40.4mm.
The next step is very simple. Place spring (with base and retainer) into the spring tester, and pull the lever. Be sure to take note of the pressure before moving onto the next spring.
The next step is to set the stop for the “open” position. In these tests we used an open lift of 0.520” The .520" lift number is just an arbitrary number we used for this example as many after market cams are around the .520 lift mark. Our KSi Cams are .535" lift.
Then place the spring assembly back into the tester and pull hard. Once again make sure you take note of the pressure.
Here is a list of some of the common valve springs people are using. Each of these measurements was done with the spring’s corresponding retainers and spring bases.
Supertech 1020D Valvesprings and Retainers kit
- 96-97lbs on the seat (installed)
- 287-288lbs open at .520" Lift
- Max lift .655
GO Power Dual Springs and Titanium Retainers kit
- 87-88lbs on the seat (installed)
- 239-240lbs open at .520" Lift
- Max lift .665
Skunk2 Pro Series Dual springs and Retainers
- 73-74lbs on the seat (installed)
- 235-236lbs open at .520" Lift
- Max lift .660
Eibach 20411.216 Dual Springs and Titanium Retainers
- 85-86lbs on the seat (installed)
- 235-236lbs open at .520" Lift
- Max lift .560
Stock 2006+ Civic Si Intake
- 55lbs on the seat (installed)
- 165lbs open at .500" Lift
- Max lift .500
Stock 2006+ Civic Si Exhaust
- 55lbs on the seat (installed)
- 160lbs open at .500" Lift
- Max lift .500
The Skunk2 and Eibach combos were tested in 2008. The GO Power and Supertech were re-tested last week.
If you would like, we can try and obtain and test other springs that people might be interested in.
1 - 1 of 41 Posts
1 - 1 of 41 Posts
