Install Guide: TWM Short Shift Kit 2006+ Honda Civic / Civic Si - Page 11

Adlh29 · 06-20-2008, 11:09 AM

A vise is also a great way to get the blue cap on the ss adapter. Be sure to use lot's of grease.

comapoet · 06-22-2008, 10:26 PM

Great diy....quick and easy and well worth the money. what a difference!

TechJunky · 06-26-2008, 11:49 PM

My only question (sorry if this was posted earlier, but I didn't see anything while reading through): How easy is it to take this adapter off? I'm thinking about getting just the short shifter, but I don't want to void the warranty and would prefer to be able to swap it back to stock if need be for servicing or warranty work (just in case, ya know)

***TWM Performance*** · 06-27-2008, 03:29 PM

Quote:

Originally Posted by TechJunky

My only question (sorry if this was posted earlier, but I didn't see anything while reading through): How easy is it to take this adapter off? I'm thinking about getting just the short shifter, but I don't want to void the warranty and would prefer to be able to swap it back to stock if need be for servicing or warranty work (just in case, ya know)

Hi TechJunky,

It is easy to remove the short shifter adapter, it's just a matter of loosening the shifter from the shift assembly and cleaning the jam nut from the dried loctite on it before installing it back on the car.

However, if you plan on removing the shifter adapter a few time, I suggest you buy it with the installed pivot cup because you could potentially damage the stock one by doing so.

Concerning the manufacturer warranty, the shifter adapter does not affect it. Plus, all of our shifters are protected by a lifetime garantee to the original buyer.

Thanks,

Frank
TWM Performance

denooch · 08-04-2008, 11:58 PM

WOW i need this. will buy soon
out of scale 1-5 how hard is this to install?

***sonej4*** · 08-07-2008, 07:47 PM

Just installed the SS and base bushings. I have the cable bushings too, but decided to wait on those. The install was very easy. The tip about removing the console was worth it. It made the install easier. Thanks for the DIY. The color pics were much better.

scooter · 08-11-2008, 03:12 PM

Ok I've got a question. I'm seeing that everyone is talking about weighted shifter knobs. What is the actuall benefit to this other than it being heavier and looking better than the stock knob? I'm getting ready to order my short shifter, bushings, and cable bushings, any help would be great as far as tips go to installing these. I konw I konw look at the instructions and posts but if there is anything out there that someone can add for ease that would be great. I'm seeing that removing the center console is the best way to go, am I correct. Thanks for the help.

MutantCheese · 08-11-2008, 05:34 PM

Newton's First Law

scooter · 08-11-2008, 05:38 PM

So is that your round about way of saying nothing, it just looks better with the heavy knob? I don't get it, and I'm not in school anymore, not for going on 14 years. In short that means I'm not trying to study newtons law for a simple answer. I'll just figure it out for myself. But thanks anyway.

MutantCheese · 08-11-2008, 05:41 PM

A weighted knob will be easier to move through the gears because "an object in motion tends to stay in motion unless acted upon by an outside source." So the heavier the knob, the more force needed to stop it's motion. Weighted knobs are better.

scooter · 08-11-2008, 05:46 PM

Ok so for you out there that want to know the answer to the same question I asked about what makes a heavy shift knob better than any other. Look at the link below. Thanks to TWM Performance for spelling it out without "Newton's Law"!

What is a Shift Knob

scooter · 08-11-2008, 05:46 PM

Thanks for the answer. I appreciate it. Seriously!

MutantCheese · 08-11-2008, 07:16 PM

Quote:

Originally Posted by scooter

Ok so for you out there that want to know the answer to the same question I asked about what makes a heavy shift knob better than any other. Look at the link below. Thanks to TWM Performance for spelling it out without "Newton's Law"!

What is a Shift Knob

hmmmm...this sounds like Newtons Law to me...

Quote:

Why is a heavier shift knob better you may ask yourself? The answer is simple and relates to basic physics. A heavy shift knob carries with it more kinetic energy and has greater momentum than a less massive (lighter) shift knob travelling at the same speed. Kinetic energy is defined as the energy possessed by a body because of its motion, equal to one half the mass of the body times the square of its speed. Momentum is defined as the product of the mass times the velocity of an object. Since kinetic energy and momentum are directly proportional to an objects mass, the more massive (heavy) an object is the more kinetic energy it carries with it through it's movement, and it has a greater momentum than a less massive object travelling at the same speed.

wgbmrx · 08-25-2008, 07:00 PM

I posted this in the Mechanical problems section but it might be better off in here. I am trying to uninstall the short shifter because I am bringing my car in to get the 3rd gear looked at and I don't want them to not fix it because of the SS. I can not seem to get the adapter off the stock part. It spins around after I took the bolt off but it wont slide off. I don't want to brake it in doing so. Any incite would be helpful. Thanks!

fordtraitor19 · 08-26-2008, 12:40 AM

Hey. Great DIY. I just put mine in and it feels amazing! Best mod so far. Thanks

**webby** · 08-26-2008, 01:55 AM

Quote:

Originally Posted by wgbmrx

I posted this in the Mechanical problems section but it might be better off in here. I am trying to uninstall the short shifter because I am bringing my car in to get the 3rd gear looked at and I don't want them to not fix it because of the SS. I can not seem to get the adapter off the stock part. It spins around after I took the bolt off but it wont slide off. I don't want to brake it in doing so. Any incite would be helpful. Thanks!

others have left it on for the 3rd gear fix without problem.

k20fg2SI · 08-26-2008, 03:32 PM

to remove the shift knob which way do you turn it?

Prankster77 · 09-02-2008, 02:44 AM

Cant wait to install mine tomorrow!

Prankster77 · 09-02-2008, 07:56 PM

Hmm well i installed mine and its awesome! only problem is that it seems to be hitting part of the shift assembly when going into 2nd 4th or 6th, it isnt enough to keep me from getting in gear but it definitely makes a little clunk going into gear. Im sure i pushed it up as far as it will go

***TWM Performance*** · 09-03-2008, 12:59 PM

Quote:

Originally Posted by Prankster77

Hmm well i installed mine and its awesome! only problem is that it seems to be hitting part of the shift assembly when going into 2nd 4th or 6th, it isnt enough to keep me from getting in gear but it definitely makes a little clunk going into gear. Im sure i pushed it up as far as it will go

Hello,

To make sure the adapter is correctly pushed down on the stock pivot arm, unscrew the tightening bolt and place a flat head screwdriver between the shift assembly and the adapter. With the shifter engaged in second gear, push on the adapter with the screwdriver to make sure the adapter is as far on the pivot arm as it can be, then tighten the bolt. It shouldn't hit on the shift assembly after that.

Frank
TWM Performance

06-22-2008, 10:26 PM	#202 (permalink)
comapoet Junior Member Join Date: Jun 2008 Location: NC Posts: 13 iTrader: 0 / 0%	Good stuff... Great diy....quick and easy and well worth the money. what a difference!

LinkBacks (?) LinkBack to this Thread: http://www.8thcivic.com/forums/transmission/16370-install-guide-twm-short-shift-kit-2006-honda-civic-civic-si.html
Posted By	For	Type	Date
Parking Brake Adjustment on 2006 Civic with Drum Brakes (Hybrid) - Honda Car Forum - Accord Parts Civic Tuning Acura Racing	This thread	Refback	02-24-2008 05:18 PM

Thread Tools
Show Printable Version Email this Page
Display Modes
Linear Mode Switch to Hybrid Mode Switch to Threaded Mode

Similar Threads
Thread	Thread Starter	Forum	Replies	Last Post
Civic SI Sedan Comes To America - Chicago Auto Show Debut	webby	Honda Industry News	11	04-19-2008 10:24 PM
2006 Honda Civic Hybrid Pricing Released	webby	Civic Hybrid	0	11-30-2005 11:08 AM
2006 honda world news	webby	Garage	0	07-25-2005 10:31 AM
2006 Civic Detailed Report	webby	Garage	2	07-06-2005 11:25 PM
2006 Geneva Civic Release	webby	Garage	0	06-23-2005 12:10 AM

06-20-2008, 11:09 AM	#201 (permalink)
Adlh29 Senior Member Join Date: Aug 2007 Location: Keystone State Posts: 767 Adam iTrader: 6 / 100%	A vise is also a great way to get the blue cap on the ss adapter. Be sure to use lot's of grease.

06-26-2008, 11:49 PM	#203 (permalink)
TechJunky Member Join Date: Jun 2008 Location: Wilkes Barre, PA Age: 23 Posts: 71 iTrader: 0 / 0%	My only question (sorry if this was posted earlier, but I didn't see anything while reading through): How easy is it to take this adapter off? I'm thinking about getting just the short shifter, but I don't want to void the warranty and would prefer to be able to swap it back to stock if need be for servicing or warranty work (just in case, ya know)

08-04-2008, 11:58 PM	#205 (permalink)
denooch Senior Member Join Date: Jun 2008 Location: PASADENA AREA Posts: 617 e iTrader: 0 / 0%	WOW i need this. will buy soon out of scale 1-5 how hard is this to install?

08-07-2008, 07:47 PM	#206 (permalink)
*sonej4* VIP Member Join Date: Jan 2007 Location: Thomaston, GA Age: 32 Posts: 1,938 Richard iTrader: 5 / 100%	Just installed the SS and base bushings. I have the cable bushings too, but decided to wait on those. The install was very easy. The tip about removing the console was worth it. It made the install easier. Thanks for the DIY. The color pics were much better.

08-11-2008, 03:12 PM	#207 (permalink)
scooter Junior Member Join Date: Mar 2008 Posts: 11 iTrader: 0 / 0%	Ok I've got a question. I'm seeing that everyone is talking about weighted shifter knobs. What is the actuall benefit to this other than it being heavier and looking better than the stock knob? I'm getting ready to order my short shifter, bushings, and cable bushings, any help would be great as far as tips go to installing these. I konw I konw look at the instructions and posts but if there is anything out there that someone can add for ease that would be great. I'm seeing that removing the center console is the best way to go, am I correct. Thanks for the help.

08-11-2008, 05:34 PM	#208 (permalink)
MutantCheese Senior Member Join Date: Aug 2006 Location: Edge of Insanity Age: 39 Posts: 3,288 2008 NFR S2000 iTrader: 0 / 0%	Newton's First Law

08-11-2008, 05:38 PM	#209 (permalink)
scooter Junior Member Join Date: Mar 2008 Posts: 11 iTrader: 0 / 0%	So is that your round about way of saying nothing, it just looks better with the heavy knob? I don't get it, and I'm not in school anymore, not for going on 14 years. In short that means I'm not trying to study newtons law for a simple answer. I'll just figure it out for myself. But thanks anyway.

08-11-2008, 05:41 PM	#210 (permalink)
MutantCheese Senior Member Join Date: Aug 2006 Location: Edge of Insanity Age: 39 Posts: 3,288 2008 NFR S2000 iTrader: 0 / 0%	A weighted knob will be easier to move through the gears because "an object in motion tends to stay in motion unless acted upon by an outside source." So the heavier the knob, the more force needed to stop it's motion. Weighted knobs are better.

08-11-2008, 05:46 PM	#211 (permalink)
scooter Junior Member Join Date: Mar 2008 Posts: 11 iTrader: 0 / 0%	Ok so for you out there that want to know the answer to the same question I asked about what makes a heavy shift knob better than any other. Look at the link below. Thanks to TWM Performance for spelling it out without "Newton's Law"! What is a Shift Knob

08-11-2008, 05:46 PM	#212 (permalink)
scooter Junior Member Join Date: Mar 2008 Posts: 11 iTrader: 0 / 0%	Thanks for the answer. I appreciate it. Seriously!

08-25-2008, 07:00 PM	#214 (permalink)
wgbmrx Junior Member Join Date: Mar 2008 Posts: 8 iTrader: 0 / 0%	I posted this in the Mechanical problems section but it might be better off in here. I am trying to uninstall the short shifter because I am bringing my car in to get the 3rd gear looked at and I don't want them to not fix it because of the SS. I can not seem to get the adapter off the stock part. It spins around after I took the bolt off but it wont slide off. I don't want to brake it in doing so. Any incite would be helpful. Thanks!

08-26-2008, 12:40 AM	#215 (permalink)
fordtraitor19 Senior Member Join Date: May 2008 Location: Alta Loma, CA Age: 20 Posts: 998 Scott iTrader: 0 / 0%	Hey. Great DIY. I just put mine in and it feels amazing! Best mod so far. Thanks

08-26-2008, 03:32 PM	#217 (permalink)
k20fg2SI Senior Member Join Date: Jun 2008 Posts: 314 iTrader: 0 / 0%	to remove the shift knob which way do you turn it?

09-02-2008, 02:44 AM	#218 (permalink)
Prankster77 Senior Member Join Date: Apr 2008 Location: Mullica Hill, NJ Age: 20 Posts: 209 Brad iTrader: 4 / 100%	Cant wait to install mine tomorrow!

09-02-2008, 07:56 PM	#219 (permalink)
Prankster77 Senior Member Join Date: Apr 2008 Location: Mullica Hill, NJ Age: 20 Posts: 209 Brad iTrader: 4 / 100%	Hmm well i installed mine and its awesome! only problem is that it seems to be hitting part of the shift assembly when going into 2nd 4th or 6th, it isnt enough to keep me from getting in gear but it definitely makes a little clunk going into gear. Im sure i pushed it up as far as it will go