Blower RPM 101 for the MP62 - 8th Generation Honda Civic Forum
8thCivic.com

Go Back   8th Generation Honda Civic Forum > Honda Civic Technical > Forced Induction And Nitrous > Supercharging

Reply
 
LinkBack Thread Tools Display Modes
Old 11-25-2012, 05:48 PM   #1 (permalink)
Team Orange
 
JDM_DOHC_SiR's Avatar
 
Join Date: Aug 2009
Location: Eastlake, San Diego
Age: 43
Posts: 33,250
Dave
Exclamation Blower RPM 101 for the MP62

OK Guys... Here is a little Blower RPM 101 of a bunch of you guys looking for info on some suggestions for Aftercoolers and "Safe" RPM on Ported/ Non-Ported blowers... now this is not writen in stone.. "but" it is a good suggestion to use this as a guide when selecting on which set up to go with..

Stock Si Crank Pulley 13810-RRB-A01
5.46 / 3.60 x 8500 = 12891
5.46 / 3.40 x 8500 = 13650
5.46 / 3.30 x 8500 = 14063
5.46 / 3.20 x 8500 = 14503
5.46 / 3.15 x 8500 = 14733
5.46 / 3.00 x 8500 = 15470 *Aftercooler recomended
5.46 / 2.90 x 8500 = 16003 *Aftercooler recomended
5.46 / 2.80 x 8500 = 16575 *Aftercooler needed
5.46 / 2.60 x 8500 = 17850 *Aftercooler+Blower porting needed/ possible belt slip


CR-V Crank Pulley 13810-RRA-A02
5.98 / 3.60 x 8500 = 14119
5.98 / 3.40 x 8500 = 14950
5.98 / 3.30 x 8500 = 15403 *Aftercooler recomended
5.98 / 3.20 x 8500 = 15884 *Aftercooler needed
5.98 / 3.15 x 8500 = 16136 *Aftercooler needed
5.98 / 3.00 x 8500 = 16943 *Aftercooler+Blower porting recomended
5.98 / 2.90 x 8500 = 17527 *Aftercooler+Blower porting needed
5.98 / 2.80 x 8500 = 18153 *Aftercooler+Blower porting needed
5.98 / 2.60 x 8500 = 19550 *Aftercooler+Blower porting needed/ possible belt slip and blower bearing issues..


2012 Si Crank Pulley 13810-R40-A02
or
2011 RDX Crank Pulley 13810-RWC-A01 Cheaper and about 2 grams lighter
6.37 / 3.60 x 8500 = 15040
6.37 / 3.40 x 8500 = 15925 *Aftercooler needed
6.37 / 3.30 x 8500 = 16407 *Aftercooler needed
6.37 / 3.20 x 8500 = 16920 *Aftercooler+Blower porting recomended
6.37 / 3.15 x 8500 = 17188 *Aftercooler+Blower porting needed
6.37 / 3.00 x 8500 = 18048 *Aftercooler+Blower porting needed
6.37 / 2.90 x 8500 = 18670 *Aftercooler+Blower porting needed/ possible blower bearing issues..
6.37 / 2.80 x 8500 = 19337 *Aftercooler+Blower porting needed/ possible blower bearing issues..
6.37 / 2.60 x 8500 = 20825 *Aftercooler+Blower porting needed/ possible belt slip and blower bearing issues..
__________________
CT Supercharged K20z3 MP62
421whp & 280ftlbs..15.5psi on 91 Oct gas

Last edited by JDM_DOHC_SiR; 03-22-2014 at 02:13 PM. Reason: more blower pulley options
JDM_DOHC_SiR is offline  
Reply With Quote Quick reply to this message
Sponsored Links
Advertisement
 
Old 11-25-2012, 06:26 PM   #2 (permalink)
there is no spoon

 
Join Date: May 2006
Posts: 16,806
thank you for making this Dave.
__________________
becauseHONDA™
mucter is offline   Reply With Quote Quick reply to this message
Old 12-09-2012, 06:01 PM   #3 (permalink)
Senior Member
 
icehockeyplaya98's Avatar
 
Join Date: Feb 2011
Location: Raleigh, NC From: Omaha, NE
Posts: 253
David
So is the new Si crank pulley the one to go with now? now TSX/CRV?
icehockeyplaya98 is offline   Reply With Quote Quick reply to this message
Old 12-13-2012, 11:24 PM   #4 (permalink)
Senior Member
 
chronic si's Avatar
 
Join Date: Jul 2007
Location: Atlanta
Posts: 787
Connor
Isn't the R40 A02 the same as the 08 accord crank pulley?
chronic si is offline   Reply With Quote Quick reply to this message
Old 02-22-2013, 09:27 AM   #5 (permalink)
1* Man
 
Steve42790's Avatar
 
Join Date: Jun 2010
Location: NJ
Posts: 19,825
Scubaaaaaaaaaaaaaaaaaaaaa
Re: Blower RPM 101 for the MP62

What about rdx cp?
Steve42790 is offline   Reply With Quote Quick reply to this message
Old 02-22-2013, 01:13 PM   #6 (permalink)
Team Orange
 
JDM_DOHC_SiR's Avatar
 
Join Date: Aug 2009
Location: Eastlake, San Diego
Age: 43
Posts: 33,250
Dave
The RDX Pulley 13810-RWC-A01 is similar in size to the R40 pulley... not to sure on exact DIA but it's lighter than the R40 one by quite a bit...and it's rather cheap too ....
looking to find more info on this pulley
__________________
CT Supercharged K20z3 MP62
421whp & 280ftlbs..15.5psi on 91 Oct gas
JDM_DOHC_SiR is offline   Reply With Quote Quick reply to this message
Old 02-22-2013, 01:19 PM   #7 (permalink)
1* Man
 
Steve42790's Avatar
 
Join Date: Jun 2010
Location: NJ
Posts: 19,825
Scubaaaaaaaaaaaaaaaaaaaaa
Re: Blower RPM 101 for the MP62

Quote:
Originally Posted by JDM_DOHC_SiR View Post
The RDX Pulley 13810-RWC-A01 is similar in size to the R40 pulley... not to sure on exact DIA but it's lighter than the R40 one by quite a bit...and it's rather cheap too ....
looking to find more info on this pulley
Yeah id like to know exactly, cuz my friend is selling one and i might buy it if i can run it without a ported blower

also how much is the rdx pulley new? this guy is sellin it to me for $60. is that a good price?

Last edited by Steve42790; 02-22-2013 at 01:25 PM.
Steve42790 is offline   Reply With Quote Quick reply to this message
Old 02-22-2013, 01:23 PM   #8 (permalink)
there is no spoon

 
Join Date: May 2006
Posts: 16,806
Quote:
Originally Posted by JDM_DOHC_SiR View Post
The RDX Pulley 13810-RWC-A01 is similar in size to the R40 pulley... not to sure on exact DIA but it's lighter than the R40 one by quite a bit...and it's rather cheap too ....
looking to find more info on this pulley
I haz one.



In my RDX.
__________________
becauseHONDA™
mucter is offline   Reply With Quote Quick reply to this message
Old 02-22-2013, 01:27 PM   #9 (permalink)
1* Man
 
Steve42790's Avatar
 
Join Date: Jun 2010
Location: NJ
Posts: 19,825
Scubaaaaaaaaaaaaaaaaaaaaa
Re: Blower RPM 101 for the MP62

Quote:
Originally Posted by mucter View Post
I haz one.



In my RDX.
lol can u go measure the diameter of ur crank pulley
Steve42790 is offline   Reply With Quote Quick reply to this message
Old 02-22-2013, 01:29 PM   #10 (permalink)
there is no spoon

 
Join Date: May 2006
Posts: 16,806
__________________
becauseHONDA™
mucter is offline   Reply With Quote Quick reply to this message
Old 02-22-2013, 01:29 PM   #11 (permalink)
there is no spoon

 
Join Date: May 2006
Posts: 16,806
It's raining like the end of days outside.
__________________
becauseHONDA™
mucter is offline   Reply With Quote Quick reply to this message
Old 02-22-2013, 01:31 PM   #12 (permalink)
there is no spoon

 
Join Date: May 2006
Posts: 16,806
And the outer diameter is not what you need. You need the diameter where the ridges are that the belt runs on. It's impossible for me to get you that without taking the belt off. Which will never happen on that car.
__________________
becauseHONDA™
mucter is offline   Reply With Quote Quick reply to this message
Old 02-22-2013, 01:32 PM   #13 (permalink)
1* Man
 
Steve42790's Avatar
 
Join Date: Jun 2010
Location: NJ
Posts: 19,825
Scubaaaaaaaaaaaaaaaaaaaaa
Re: Blower RPM 101 for the MP62

Quote:
Originally Posted by mucter View Post
And the outer diameter is not what you need. You need the diameter where the ridges are that the belt runs on. It's impossible for me to get you that without taking the belt off. Which will never happen on that car.


i found it online from acura for $28?! its that cheap??
Steve42790 is offline   Reply With Quote Quick reply to this message
Old 02-22-2013, 01:39 PM   #14 (permalink)
there is no spoon

 
Join Date: May 2006
Posts: 16,806
That's funny if it's only used on the RDX. The RDX didn't exactly sell in high volumes.
__________________
becauseHONDA™
mucter is offline   Reply With Quote Quick reply to this message
Old 02-22-2013, 01:48 PM   #15 (permalink)
1* Man
 
Steve42790's Avatar
 
Join Date: Jun 2010
Location: NJ
Posts: 19,825
Scubaaaaaaaaaaaaaaaaaaaaa
Re: Blower RPM 101 for the MP62

Quote:
Originally Posted by mucter View Post
That's funny if it's only used on the RDX. The RDX didn't exactly sell in high volumes.
whats funny?
Steve42790 is offline   Reply With Quote Quick reply to this message
Old 02-22-2013, 01:48 PM   #16 (permalink)
Team Orange
 
JDM_DOHC_SiR's Avatar
 
Join Date: Aug 2009
Location: Eastlake, San Diego
Age: 43
Posts: 33,250
Dave
Quote:
Originally Posted by Steve42790 View Post


i found it online from acura for $28?! its that cheap??
Thats about the price they sell for 28~39$

Buy it and measure it for us .... measure it from Peak to Peak on where the belt rests.. so we can add a pulley to the line up if it's different

Also looking at adding the Monster 4G TL pulley to the line up if there is anyone crazy enought to use it
__________________
CT Supercharged K20z3 MP62
421whp & 280ftlbs..15.5psi on 91 Oct gas
JDM_DOHC_SiR is offline   Reply With Quote Quick reply to this message
Old 02-22-2013, 01:59 PM   #17 (permalink)
Team Orange
 
JDM_DOHC_SiR's Avatar
 
Join Date: Aug 2009
Location: Eastlake, San Diego
Age: 43
Posts: 33,250
Dave




__________________
CT Supercharged K20z3 MP62
421whp & 280ftlbs..15.5psi on 91 Oct gas
JDM_DOHC_SiR is offline   Reply With Quote Quick reply to this message
Old 02-22-2013, 02:01 PM   #18 (permalink)
1* Man
 
Steve42790's Avatar
 
Join Date: Jun 2010
Location: NJ
Posts: 19,825
Scubaaaaaaaaaaaaaaaaaaaaa
Re: Blower RPM 101 for the MP62

Quote:
Originally Posted by JDM_DOHC_SiR View Post
Thats about the price they sell for 28~39$

Buy it and measure it for us .... measure it from Peak to Peak on where the belt rests.. so we can add a pulley to the line up if it's different

Also looking at adding the Monster 4G TL pulley to the line up if there is anyone crazy enought to use it
I will buy it if i can confirm i wont have a problem using it with an unported blower and 3" pulley lol.

and which pullies are in those pics??





Quote:
Originally Posted by JDM_DOHC_SiR View Post
Steve42790 is offline   Reply With Quote Quick reply to this message
Old 02-22-2013, 02:15 PM   #19 (permalink)
1* Man
 
Steve42790's Avatar
 
Join Date: Jun 2010
Location: NJ
Posts: 19,825
Scubaaaaaaaaaaaaaaaaaaaaa
Re: Blower RPM 101 for the MP62

anyone know about any of the other pullies such as accord, or other acura models like the mdx?
Steve42790 is offline   Reply With Quote Quick reply to this message
Old 02-22-2013, 02:17 PM   #20 (permalink)
1* Man
 
Steve42790's Avatar
 
Join Date: Jun 2010
Location: NJ
Posts: 19,825
Scubaaaaaaaaaaaaaaaaaaaaa
Re: Blower RPM 101 for the MP62

fuck it! im just gonna order the rdx pulley.
Steve42790 is offline   Reply With Quote Quick reply to this message
Sponsored Links
Advertisement
 
Reply

Quick Reply
Message:
Options

Register Now

In order to be able to post messages on the 8th Generation Honda Civic Forum forums, you must first register.
Please enter your desired user name, your email address and other required details in the form below.
User Name:
Password
Please enter a password for your user account. Note that passwords are case-sensitive.
Password:
Confirm Password:
Email Address
Please enter a valid email address for yourself.
Email Address:

Log-in

Human Verification

In order to verify that you are a human and not a spam bot, please enter the answer into the following box below based on the instructions contained in the graphic.



Thread Tools
Display Modes

Posting Rules
You may post new threads
You may post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off
Trackbacks are On
Pingbacks are On
Refbacks are On


Similar Threads
Thread Thread Starter Forum Replies Last Post
Blower with e85 Zib331 Supercharging 3 09-25-2011 12:00 AM
anyone think the blower fan sucks? SmokeShank Mechanical Problems & Technical Chat 9 07-26-2011 08:22 PM
AC blower? 2007BlueCivic Mechanical Problems & Technical Chat 1 10-11-2010 06:06 PM
A Leaf Blower Blower LoverOfCivics Forced Induction And Nitrous 3 07-19-2009 07:38 PM
Day 4 with my CT Blower... onefastsi Supercharging 49 11-07-2008 01:46 PM


All times are GMT -4. The time now is 09:28 PM.



Powered by vBulletin® Copyright ©2000 - 2014, Jelsoft Enterprises Ltd.
Content Relevant URLs by vBSEO 3.6.0
Garage Plus vBulletin Plugins by Drive Thru Online, Inc.
copyright 8thcivic.com - all rights reserved