broken shifter cable?

hialeahzbg · 12-31-2007, 04:29 AM

Well I have a 07 si....had it for like 4 months now and a month after I bought I installed shifter bushings....I bent the assembly its on.... so shifting was kinda hard but still drivable...2day driving home it pops out of 3rd gear and the shifter goes everywhere....I'm thinking the pin came off of something...I pulled over and pop my hood and see that cable broke where it meets the ring that goes in the pin...I can't take it back 2 honda because they will say I broke it which I kinda did....anyone know if the fix is expensive?

Asif22 · 12-31-2007, 04:38 AM

Probably not all you need is the pin right? You can probably get one at home depot. If you need the bushing just order the bushings again which is like 50 bucks I think.

hialeahzbg · 12-31-2007, 05:30 AM

Its not the pin that broke...its the actual ring that's on the on of the cable...imy car has the X intake and exhaust so I void my warranty....I would need 2 buy one cable if they sell one and that piece where its on....so the shifting won't be rough anymore...

dc5jimbo · 12-31-2007, 05:33 AM

Quote:

Originally Posted by hialeahzbg

Its not the pin that broke...its the actual ring that's on the on of the cable...imy car has the X intake and exhaust so I void my warranty....I would need 2 buy one cable if they sell one and that piece where its on....so the shifting won't be rough anymore...

i would try to go to honda any ways maby if u can really really butter thme up thell hook u up and sorry to hear the bad news.

12-31-2007, 04:29 AM	#1 (permalink)
hialeahzbg Senior Member Join Date: Aug 2007 Location: SoFlo...305* Posts: 293 iTrader: 0 / 0%	broken shifter cable? Well I have a 07 si....had it for like 4 months now and a month after I bought I installed shifter bushings....I bent the assembly its on.... so shifting was kinda hard but still drivable...2day driving home it pops out of 3rd gear and the shifter goes everywhere....I'm thinking the pin came off of something...I pulled over and pop my hood and see that cable broke where it meets the ring that goes in the pin...I can't take it back 2 honda because they will say I broke it which I kinda did....anyone know if the fix is expensive?

Thread Tools
Show Printable Version Email this Page
Display Modes
Linear Mode Switch to Hybrid Mode Switch to Threaded Mode

Similar Threads
Thread	Thread Starter	Forum	Replies	Last Post
DIY part II: Cable Shifter bushings (Big Pictures inside)	atruhondagrl	Transmission	87	11-29-2008 11:02 AM
BROKEN shifter cable ;-(	Streethonda06	Mechanical Problems & Technical Chat	22	09-20-2008 03:33 PM
2007 Civic Shifter Cable Bushings!	TWM Performance	TWM Performance Short Shifters	23	04-26-2007 03:55 PM
TWM Shifter Cable Bushings	TWM Performance	TWM Performance Short Shifters	0	03-19-2007 06:14 PM
twm's new shifter cable bushings (bronzoil)	acrobles	Garage	3	03-02-2007 03:54 AM

12-31-2007, 04:38 AM	#2 (permalink)
Asif22 Senior Member Join Date: Jul 2007 Location: United States Posts: 2,808 Mohamed El-Mubaslat iTrader: 0 / 0%	Probably not all you need is the pin right? You can probably get one at home depot. If you need the bushing just order the bushings again which is like 50 bucks I think.

12-31-2007, 05:30 AM	#3 (permalink)
hialeahzbg Senior Member Join Date: Aug 2007 Location: SoFlo...305* Posts: 293 iTrader: 0 / 0%	Its not the pin that broke...its the actual ring that's on the on of the cable...imy car has the X intake and exhaust so I void my warranty....I would need 2 buy one cable if they sell one and that piece where its on....so the shifting won't be rough anymore...