DIY: Install guide for OEM fogs... - Page 2

f14fighter · 02-28-2007, 11:16 PM

You will need a wire extractor or awl to push the pin in to extract the wire.

Chase · 02-28-2007, 11:36 PM

I did a simaler cut on that foglight hole just to allow more airflow for my CAI..

grcivicsi06 · 04-04-2007, 05:24 PM

This thread should be stickied!! Thanks for making it....the 6 pin connector step is not mentioned in any instruction, and you got me straightened out. Thanks much!

darna · 04-04-2007, 05:31 PM

^^its already been stickied long time ago.

grcivicsi06 · 04-04-2007, 06:10 PM

Quote:

Originally Posted by darna

^^its already been stickied long time ago.

I know, I should have written it this way. It SHOULD be stickied as in it it belongs here and is very useful

**ImTheVoiceOfGod** · 04-13-2007, 09:00 PM

Can someone tell me the purpose of drilling the holes from the template? I dont see what they are used for.

vtmn215 · 04-13-2007, 09:03 PM

in the instructions, the template for the hole needs to be drilled so you can access the fog light adjusting screw.

**ImTheVoiceOfGod** · 04-13-2007, 09:05 PM

Ahhhhh, thanks

+rep

vtmn215 · 04-13-2007, 09:43 PM

Hooo Ya!

I didn't know why we needed to drill those holes till I saw the foglight mounting bracket.

**ImTheVoiceOfGod** · 04-14-2007, 10:01 PM

Ok,I was installing aftermarket fogs. I finished the install last night, everything works.... but I have a blue connecter left..... Where the **** does this go????

vtmn215 · 04-15-2007, 02:38 AM

blue connector... 6 pin?... IIR the fuse box... lemme go check. Ya blue connector into the fuse box. In the fuse box, you will see 3 big runs of cable connected to the box. Starting from the top to the bottom, green, white and blue. Right below the blue connector on its left hand side, you will see an open spot, the blue 6-pin connector goes there.

**ImTheVoiceOfGod** · 04-15-2007, 02:17 PM

Already did that one, theres another connecter that is the EXACT same as the female side of the blue one you are talking about.

vtmn215 · 04-15-2007, 03:23 PM

I havent the foggiest idea LOL.. I looked at the K2 kit that i have in my garage and saw that cable too... I ended up installing the OEM fog light kit for my 07 si. So now, I have an extra fog light kit in case mine gets broken meh. All I know is that if it works, don't fix it

***truflip*** · 04-15-2007, 09:00 PM

is the k2 supposed to come with 15A fuse? the OEM comes with 20A..

**ImTheVoiceOfGod** · 04-15-2007, 09:01 PM

Mine came with 15A, I used it and it works.

***truflip*** · 04-15-2007, 10:21 PM

ok so i can go ahead with the instal.. thanks bro!

**ImTheVoiceOfGod** · 04-15-2007, 10:24 PM

wErd. Let me know how it goes.

irichard · 04-19-2007, 11:29 PM

will be using guide soon

***truflip*** · 04-19-2007, 11:37 PM

sunny warm weather is in forecast! mine will be going on Sunday/Monday

wheee!

taffysi · 04-21-2007, 01:00 AM

How do you get the black plastic bolts off from the bottom? I used a flat head screw driver and flathead pliers and I manage to get the front 6 off but not the 4 inner ones. They just wont budge! Yes, I tried to pry the center of the bolt.

04-15-2007, 02:38 AM	#31 (permalink)
vtmn215 Senior Member Join Date: Feb 2007 Location: Houston Age: 32 Posts: 393	blue connector... 6 pin?... IIR the fuse box... lemme go check. Ya blue connector into the fuse box. In the fuse box, you will see 3 big runs of cable connected to the box. Starting from the top to the bottom, green, white and blue. Right below the blue connector on its left hand side, you will see an open spot, the blue 6-pin connector goes there. Last edited by vtmn215; 04-15-2007 at 02:43 AM.

Thread Tools
Show Printable Version Email this Page
Display Modes
Linear Mode Switch to Hybrid Mode Switch to Threaded Mode

LinkBacks (?) LinkBack to this Thread: http://www.8thcivic.com/forums/lighting/13214-diy-install-guide-oem-fogs.html
Posted By	For	Type	Date
Installation de fog? - Club Civic Quebec :: Forum	This thread	Refback	09-13-2011 03:30 AM
Installation de fog? - Club Civic Quebec :: Forum	This thread	Refback	08-21-2011 10:46 PM
Installation de fog? - Club Civic Quebec :: Forum	This thread	Refback	08-20-2011 12:27 PM
Installation de fog? - Club Civic Quebec :: Forum	This thread	Refback	08-19-2011 09:08 PM
ClickProtect	This thread	Refback	02-25-2008 05:51 PM
The Temple of VTEC - Honda and Acura Enthusiasts Online Forums > Civic > > Re: Fog light install	This thread	Refback	02-19-2008 11:29 PM
The Temple of VTEC - Honda and Acura Enthusiasts Online Forums > Civic > > Re: Fog light install	This thread	Refback	02-11-2008 05:20 AM
Lighting [Archive] - 8th Generation Honda Civic Forum	This thread	Refback	02-06-2008 02:45 PM
The Temple of VTEC - Honda and Acura Enthusiasts Online Forums > Civic > > Re: Fog light install	This thread	Refback	01-21-2008 11:41 PM
DIY/install index - LOOK HERE BEFORE ASKING FOR A DIY - 8th Generation Honda Civic Forum	This thread	Refback	01-19-2008 11:59 PM
DIY: Install guide for OEM fogs... - Page 7 - 8th Generation Honda Civic Forum	This thread	Refback	01-16-2008 08:27 PM
DIY/install index - LOOK HERE BEFORE ASKING FOR A DIY - 8th Generation Honda Civic Forum	This thread	Refback	01-01-2008 08:48 PM
The Temple of VTEC - Honda and Acura Enthusiasts Online Forums > Civic > > Re: Fog light install	This thread	Refback	12-12-2007 06:18 PM
Fog lights install - Page 6 - 8th Generation Honda Civic Forum	This thread	Refback	12-09-2007 05:22 PM
8th Generation Honda Civic Forum	This thread	Refback	12-06-2007 11:54 AM

Similar Threads
Thread	Thread Starter	Forum	Replies	Last Post
DIY: Injen CAI install on R18 (lots of pics)	peliROJO	Engine	168	02-04-2012 02:53 PM
XenonDepot HID Install Guide	unplugged	Lighting, H.I.D.'s, & Neon	102	01-29-2012 05:31 PM
2006 Civic Rear Speaker Install Guide	webby	Audio	36	10-18-2011 09:12 PM
HID xenondepot install guide	webby	Lighting	66	10-18-2011 08:05 PM
DIY install of new head unit in sedan UK/AUS	aussiebuddha	I.C.E., Electrical, Security, & Navigation	4	04-04-2006 03:30 PM

02-28-2007, 11:16 PM	#21 (permalink)
f14fighter Senior Member Join Date: Feb 2007 Age: 36 Posts: 286	You will need a wire extractor or awl to push the pin in to extract the wire.

02-28-2007, 11:36 PM	#22 (permalink)
Chase Senior Member Join Date: Jul 2006 Location: Copperas Cove, TX Age: 26 Posts: 5,577 Chase	I did a simaler cut on that foglight hole just to allow more airflow for my CAI..

04-04-2007, 05:24 PM	#23 (permalink)
grcivicsi06 Senior Member Join Date: Mar 2006 Location: NW Pa Age: 50 Posts: 240	This thread should be stickied!! Thanks for making it....the 6 pin connector step is not mentioned in any instruction, and you got me straightened out. Thanks much!

04-04-2007, 05:31 PM	#24 (permalink)
darna Senior Member Join Date: Nov 2006 Location: Anaheim Posts: 5,041 xtian	^^its already been stickied long time ago.

04-13-2007, 09:00 PM	#26 (permalink)
ImTheVoiceOfGod Join Date: Dec 2006 Location: Waynesboro PA Age: 30 Posts: 38,271 Curtis	Can someone tell me the purpose of drilling the holes from the template? I dont see what they are used for.

04-13-2007, 09:03 PM	#27 (permalink)
vtmn215 Senior Member Join Date: Feb 2007 Location: Houston Age: 32 Posts: 393	in the instructions, the template for the hole needs to be drilled so you can access the fog light adjusting screw.

04-13-2007, 09:05 PM	#28 (permalink)
ImTheVoiceOfGod Join Date: Dec 2006 Location: Waynesboro PA Age: 30 Posts: 38,271 Curtis	Ahhhhh, thanks +rep

04-13-2007, 09:43 PM	#29 (permalink)
vtmn215 Senior Member Join Date: Feb 2007 Location: Houston Age: 32 Posts: 393	Hooo Ya! I didn't know why we needed to drill those holes till I saw the foglight mounting bracket.

04-14-2007, 10:01 PM	#30 (permalink)
ImTheVoiceOfGod Join Date: Dec 2006 Location: Waynesboro PA Age: 30 Posts: 38,271 Curtis	Ok,I was installing aftermarket fogs. I finished the install last night, everything works.... but I have a blue connecter left..... Where the **** does this go????

04-15-2007, 02:17 PM	#32 (permalink)
ImTheVoiceOfGod Join Date: Dec 2006 Location: Waynesboro PA Age: 30 Posts: 38,271 Curtis	Already did that one, theres another connecter that is the EXACT same as the female side of the blue one you are talking about.

04-15-2007, 03:23 PM	#33 (permalink)
vtmn215 Senior Member Join Date: Feb 2007 Location: Houston Age: 32 Posts: 393	I havent the foggiest idea LOL.. I looked at the K2 kit that i have in my garage and saw that cable too... I ended up installing the OEM fog light kit for my 07 si. So now, I have an extra fog light kit in case mine gets broken meh. All I know is that if it works, don't fix it

04-15-2007, 09:00 PM	#34 (permalink)
*truflip* VIP Member Join Date: Dec 2006 Location: Ottawa, ON Posts: 12,328 karlitO	is the k2 supposed to come with 15A fuse? the OEM comes with 20A..

04-15-2007, 09:01 PM	#35 (permalink)
ImTheVoiceOfGod Join Date: Dec 2006 Location: Waynesboro PA Age: 30 Posts: 38,271 Curtis	Mine came with 15A, I used it and it works.

04-15-2007, 10:21 PM	#36 (permalink)
*truflip* VIP Member Join Date: Dec 2006 Location: Ottawa, ON Posts: 12,328 karlitO	ok so i can go ahead with the instal.. thanks bro!

04-15-2007, 10:24 PM	#37 (permalink)
ImTheVoiceOfGod Join Date: Dec 2006 Location: Waynesboro PA Age: 30 Posts: 38,271 Curtis	wErd. Let me know how it goes.

04-19-2007, 11:29 PM	#38 (permalink)
irichard Senior Member Join Date: Sep 2005 Posts: 1,112 ****	will be using guide soon

04-19-2007, 11:37 PM	#39 (permalink)
*truflip* VIP Member Join Date: Dec 2006 Location: Ottawa, ON Posts: 12,328 karlitO	sunny warm weather is in forecast! mine will be going on Sunday/Monday wheee!

04-21-2007, 01:00 AM	#40 (permalink)
taffysi Senior Member Join Date: Oct 2006 Posts: 863	How do you get the black plastic bolts off from the bottom? I used a flat head screw driver and flathead pliers and I manage to get the front 6 off but not the 4 inner ones. They just wont budge! Yes, I tried to pry the center of the bolt.

Remove Advertisements Sponsored Links
8th Generation Honda Civic Forum Advertisement