AJR Honda Fit at J's Racing Japan (Its not a civic but its a Honda)

AJR-CoW · 08-13-2007, 12:28 AM

Just got bored so decided to do a write up about our AJR Fit No.2

Some of your guys might know that I have sent our AJR Fit to J's Racing for parts development. The AJR Fit left Vancouver (AJR Home base) Oct 2006.

When it arrived to J's Racing (Osaka Japan) it has been sitting there "chilling" with other J's Racing Demo cars

Hanging around with the REAL JDM Family

After a couple weeks of sitting. J's Racing finally got some time to look at the car. They finally realize the car looked different than the JDM Fit LOL They have tested and pre-fit all the aero parts.

I have suggested to J's Racing to build a front aero spoiler and Sport grille based on the existing style that J's Racing is selling for the JDM Fit then they have started to work on it.

Process of making the Aero lip for USDM Fit.

Q: How come the Fit has an Orange bumper

A: It is off from the AJR Time attack Fit :LOL:

The Grille finally fitted on as well. Now after all the pieces have been fitted and these parts are sent to the FRP factory for building the mold.

Suspension was the next part that has been worked on :)

- J's Racing Lower tie bar fitted and installed

- J's Racing Fender braces fitted and installed

J's Racing measured the differences between USDM and JDM suspension.

J's Racing Showa dampers fitted and installed. J's Racing made adjustment in the valving and fitment. Front swaybar end-links were replaced for J's Racing damper fitment.

The rear worked out fine.

J's Racing rotor and brake pads fitted and installed.

The J's Racing strut bars, we all knew they worked. With the install of the C-pillar bar and rear strut bar, J's Racing added on 2 addtional pieces to reinforce the back end of the chassis.

Let's move on to the I/H/E (Intake / Header / Exhaust)

The 50RS and the header fitted on with no problems but the muffler was a little too short because the USDM has a longer bumper. J's Racing is still deciding to see if they will extend the muffler for USDM Fit rear bumper.

- J's Racing muffler fitted and installed.

- J's Racing header fitted and installed.

One of the hardest part was the intake. The Tsuchinoko (sausage) portion fitted with no problems but the sensor hole and cold air portion's fitment were way off so J's Racing made adjustment for USDM Fitment.

They finally got that done but it took them almost 3 months to do.... YES WTF

:LOL:

The car is done and it is on it's way back home FINALLY !!!

The Fit is still insured so I can drive it home as soon as it hits the port :)

Thanks

Calvin

06CivicSi06 · 08-13-2007, 12:31 AM

Hot!!!!

Black_civic_Si · 08-13-2007, 12:32 AM

damn that's hot

hapaboy310 · 08-13-2007, 02:08 AM

is j's going to make an intake for the usdm fg and fa???

**marc-o-lishuz** · 08-13-2007, 02:18 AM

OMG! That's pure JDM tuning right there! I'm willing to have my FG2 sent to J's Racing in Japan for some goodies

BTW - How much is it to ship a car to Osaka?

***shglbmx*** · 08-13-2007, 03:00 AM

i think i saw you use "j's racing" at least 600 times in that post. nonetheless j's racing j's racing j's racing j's racing j's racing is awesome.

Firestrife · 08-13-2007, 03:59 AM

wow thats a bad a** Fit.

2006exsedan · 08-13-2007, 04:22 AM

uhhh whats with that wing ? other then the wing .. nicely done ..

1chin3s3_b0i · 08-13-2007, 04:47 AM

damn that fit is hot! that wing looks G on that ride too

GORDATA · 08-13-2007, 08:10 AM

Nice looking Fit, I would rock it for sure!!!

1stk20z3 · 08-13-2007, 08:18 AM

i want a J's racing lip for the HFP lip. the Hasport Si had it!

unbreakable · 08-13-2007, 08:19 AM

everything looks where it should be! man i envy you...

asdf0123 · 08-13-2007, 12:48 PM

whoa facelift for sure..nice stuff man!

berlinas2k2 · 08-13-2007, 02:14 PM

Fit looks sweet, but i think that i'd have chosen a different wing. something similar to the EG/EK civic hatch's rear spoilers...Not a fan of the boeing 747 look...

1.8L FG KiDd · 08-13-2007, 02:41 PM

wow....the sicknessssss!!

Ep3racer954 · 08-13-2007, 03:21 PM

wow i wanna hear how that thing sounds! i love the fit!

cornerstrike · 08-13-2007, 05:04 PM

Please gives us an update when you receive the Fit. Pics, vids, and driving impressions would be great!!!!

nese005 · 08-13-2007, 05:22 PM

dont really like fits but that a bad ass fit!!

cobra9244 · 08-13-2007, 05:25 PM

Nice ride. I can feel the hit!!!!!!

AJR-CoW · 08-13-2007, 05:28 PM

Quote:

Originally Posted by cornerstrike

Please gives us an update when you receive the Fit. Pics, vids, and driving impressions would be great!!!!

i will post more pics of our fits soon

08-13-2007, 12:28 AM	#1 (permalink)
AJR-CoW Senior Member Member Join Date: Jun 2007 Location: Vancouver BC Posts: 173 iTrader: 1 / 100%	AJR Honda Fit at J's Racing Japan (Its not a civic but its a Honda) Just got bored so decided to do a write up about our AJR Fit No.2 Some of your guys might know that I have sent our AJR Fit to J's Racing for parts development. The AJR Fit left Vancouver (AJR Home base) Oct 2006. When it arrived to J's Racing (Osaka Japan) it has been sitting there "chilling" with other J's Racing Demo cars Hanging around with the REAL JDM Family After a couple weeks of sitting. J's Racing finally got some time to look at the car. They finally realize the car looked different than the JDM Fit LOL They have tested and pre-fit all the aero parts. I have suggested to J's Racing to build a front aero spoiler and Sport grille based on the existing style that J's Racing is selling for the JDM Fit then they have started to work on it. Process of making the Aero lip for USDM Fit. Q: How come the Fit has an Orange bumper A: It is off from the AJR Time attack Fit :LOL: The Grille finally fitted on as well. Now after all the pieces have been fitted and these parts are sent to the FRP factory for building the mold. Suspension was the next part that has been worked on :) - J's Racing Lower tie bar fitted and installed - J's Racing Fender braces fitted and installed J's Racing measured the differences between USDM and JDM suspension. J's Racing Showa dampers fitted and installed. J's Racing made adjustment in the valving and fitment. Front swaybar end-links were replaced for J's Racing damper fitment. The rear worked out fine. J's Racing rotor and brake pads fitted and installed. The J's Racing strut bars, we all knew they worked. With the install of the C-pillar bar and rear strut bar, J's Racing added on 2 addtional pieces to reinforce the back end of the chassis. Let's move on to the I/H/E (Intake / Header / Exhaust) The 50RS and the header fitted on with no problems but the muffler was a little too short because the USDM has a longer bumper. J's Racing is still deciding to see if they will extend the muffler for USDM Fit rear bumper. - J's Racing muffler fitted and installed. - J's Racing header fitted and installed. One of the hardest part was the intake. The Tsuchinoko (sausage) portion fitted with no problems but the sensor hole and cold air portion's fitment were way off so J's Racing made adjustment for USDM Fitment. They finally got that done but it took them almost 3 months to do.... YES WTF :LOL: The car is done and it is on it's way back home FINALLY !!! The Fit is still insured so I can drive it home as soon as it hits the port :) Thanks Calvin

08-13-2007, 02:18 AM	#5 (permalink)
marc-o-lishuz Doraemon! Join Date: Apr 2006 Location: Vancouver, BC Age: 26 Posts: 23,974 Marc iTrader: 2 / 100%	OMG! That's pure JDM tuning right there! I'm willing to have my FG2 sent to J's Racing in Japan for some goodies BTW - How much is it to ship a car to Osaka? __________________ forum rules / whistler06 / whistler07 / harrison08 / flickr

08-13-2007, 03:00 AM	#6 (permalink)
*shglbmx* Pre Paid Legal Associate Join Date: Jul 2006 Location: Westminster, CA 714 Age: 21 Posts: 1,313 Daniel Tam iTrader: 14 / 100%	i think i saw you use "j's racing" at least 600 times in that post. nonetheless j's racing j's racing j's racing j's racing j's racing is awesome. __________________ Now recruiting for new car team members! Contact me for more info. Show quality cars only! Preferably local and a 4dr Si.

Thread Tools
Show Printable Version Email this Page
Display Modes
Linear Mode Switch to Hybrid Mode Switch to Threaded Mode

Similar Threads
Thread	Thread Starter	Forum	Replies	Last Post
The Where is the Car I Want Thread - ANY STATE	cbondhonda	New Car-Buying Information	336	09-22-2008 11:46 PM
2007 Honda Fit	webby	Garage	27	07-19-2008 12:48 PM
2006 honda world news	webby	Garage	0	07-25-2005 09:31 AM

08-13-2007, 12:31 AM	#2 (permalink)
06CivicSi06 Member Join Date: May 2006 Location: Chicago, IL Age: 22 Posts: 96 iTrader: 1 / 100%	Hot!!!!

08-13-2007, 12:32 AM	#3 (permalink)
Black_civic_Si Senior Member Join Date: May 2006 Location: Oakland, Bay Area Posts: 958 iTrader: 2 / 100%	damn that's hot

08-13-2007, 02:08 AM	#4 (permalink)
hapaboy310 Senior Member Join Date: May 2007 Location: south bay, cali Posts: 235 iTrader: 0 / 0%	is j's going to make an intake for the usdm fg and fa???

08-13-2007, 03:59 AM	#7 (permalink)
Firestrife Senior Member Join Date: May 2007 Location: Gainesville, FL Age: 20 Posts: 3,373 Keenan iTrader: 9 / 100%	wow thats a bad a** Fit.

08-13-2007, 04:22 AM	#8 (permalink)
2006exsedan Senior Member Join Date: Jan 2006 Location: New Bedford, MA Age: 29 Posts: 1,018 Tom iTrader: 7 / 100%	uhhh whats with that wing ? other then the wing .. nicely done ..

08-13-2007, 04:47 AM	#9 (permalink)
1chin3s3_b0i Senior Member Join Date: Aug 2006 Location: East Vancouver Age: 22 Posts: 10,513 Michael iTrader: 2 / 100%	damn that fit is hot! that wing looks G on that ride too

08-13-2007, 08:10 AM	#10 (permalink)
GORDATA Senior Member Join Date: Apr 2007 Location: The Hood, NYC Posts: 489 Big Daddy Surge iTrader: 5 / 100%	Nice looking Fit, I would rock it for sure!!!

08-13-2007, 08:18 AM	#11 (permalink)
1stk20z3 Senior Member Join Date: Apr 2006 Location: Hawaii Age: 20 Posts: 1,804 Casey iTrader: 0 / 0%	i want a J's racing lip for the HFP lip. the Hasport Si had it!

08-13-2007, 08:19 AM	#12 (permalink)
unbreakable Senior Member Join Date: Aug 2007 Location: Manila, Philippines Age: 22 Posts: 571 iTrader: 0 / 0%	everything looks where it should be! man i envy you...

08-13-2007, 12:48 PM	#13 (permalink)
asdf0123 Senior Member Join Date: Jul 2007 Location: weRk-N-progr3ss Posts: 4,079 JamEs iTrader: 4 / 100%	whoa facelift for sure..nice stuff man!

08-13-2007, 02:14 PM	#14 (permalink)
berlinas2k2 Senior Member Member Join Date: Jan 2007 Location: Vtecc'n in da Mugen' Posts: 4,748 254whp on 75 iTrader: 16 / 100%	Fit looks sweet, but i think that i'd have chosen a different wing. something similar to the EG/EK civic hatch's rear spoilers...Not a fan of the boeing 747 look...

08-13-2007, 02:41 PM	#15 (permalink)
1.8L FG KiDd Senior Member Join Date: Dec 2006 Location: I haz phat butt... Posts: 2,425 FrAnCiS iTrader: 1 / 100%	wow....the sicknessssss!!

08-13-2007, 03:21 PM	#16 (permalink)
Ep3racer954 Senior Member Join Date: Aug 2005 Location: Pompano Beach, Fl Age: 19 Posts: 1,672 FG*SQUAD #87 iTrader: 3 / 100%	wow i wanna hear how that thing sounds! i love the fit!

08-13-2007, 05:04 PM	#17 (permalink)
cornerstrike Senior Member Join Date: Jul 2006 Posts: 626 iTrader: 4 / 100%	Please gives us an update when you receive the Fit. Pics, vids, and driving impressions would be great!!!!

08-13-2007, 05:22 PM	#18 (permalink)
nese005 Senior Member Join Date: Nov 2006 Location: 614 ohio Posts: 1,569 Panda iTrader: 1 / 100%	dont really like fits but that a bad ass fit!!

08-13-2007, 05:25 PM	#19 (permalink)
cobra9244 Senior Member Join Date: Jul 2007 Location: New York Posts: 141 iTrader: 2 / 100%	Nice ride. I can feel the hit!!!!!!