jdm emblems

fhound258 · 05-09-2008, 12:41 PM

so i ordered my jdm over lays from grafixpressions, and soon realized that u need the ep3 and the dc5 jdm emblems for it to work...felt pretty stupid after ordering them. but anyways, i really want the red emblems! if i order the ep3 and dc5 emblems do i just stick it over the stock? how does it work? i don't know anyone that has done this so it would be my first time!

tsltd · 05-09-2008, 12:42 PM

no you need to take them off look for the DIY exterior mods

k20z3 Koop · 05-09-2008, 12:49 PM

http://www.grafixpressions.com/overlay_install.shtml

pgFA · 05-09-2008, 12:51 PM

This one is for FA5 but I think its pretty similar.

*DIY* '07 Si 4DR JDM/red badges

fhound258 · 05-12-2008, 01:40 AM

thanks for that dyi, i got a 2dr but got the idea. see i got the overlays thinking they go over our stock ones but then realized that u need the orginal jdm emblems, so im just going to get those, btw if any one wants those overlays ill sell them dirt cheap.

boltuprite · 05-12-2008, 09:05 AM

I got my JDM emblems on Friday and it took me about 1/2 an hour to install them. The back is a piece of cake as all you do is pull up the original emblem. (i just pushed on the tabs from the trunk and out it came. then just pushed the holding tabs out with a pair of pliers, and siliconed the 2 little holes left in the trunk. The JDM emblem fit almost exactly to size where the old one was.

The front was a bit tougher but if you follow the DYI and take the grill out, it's easy. Toughest part is reaching those little phillips screws that hold the grill on. Make sure you have stubby screwdriver or a phillips ratchet attachement with an angling head. You will also need an allen wrench to take the initial two bolts out that anchors the grill bracket.

Alternately you can just pry the front one off if you can't be bothered removing the grill, but beware as the emblem is screwed on so you woule never be able to use it again. Also you would still ahve to drill ut the screws that would be left. I thinks it's worth the extra effort to take the grill out.

The front one went right into the same holes as the stock emblem.

I'll post some pics of the finished job soon

zackster · 08-05-2008, 10:44 PM

good looking you just asnwered my question i beenloking for for awhilee....

05-09-2008, 12:41 PM	#1 (permalink)
fhound258 Senior Member Member Join Date: Feb 2006 Posts: 577	jdm emblems so i ordered my jdm over lays from grafixpressions, and soon realized that u need the ep3 and the dc5 jdm emblems for it to work...felt pretty stupid after ordering them. but anyways, i really want the red emblems! if i order the ep3 and dc5 emblems do i just stick it over the stock? how does it work? i don't know anyone that has done this so it would be my first time!
	Tweet

05-12-2008, 09:05 AM	#6 (permalink)
boltuprite Senior Member Join Date: Aug 2007 Location: Toronto Posts: 710 Gary	I got my JDM emblems on Friday and it took me about 1/2 an hour to install them. The back is a piece of cake as all you do is pull up the original emblem. (i just pushed on the tabs from the trunk and out it came. then just pushed the holding tabs out with a pair of pliers, and siliconed the 2 little holes left in the trunk. The JDM emblem fit almost exactly to size where the old one was. The front was a bit tougher but if you follow the DYI and take the grill out, it's easy. Toughest part is reaching those little phillips screws that hold the grill on. Make sure you have stubby screwdriver or a phillips ratchet attachement with an angling head. You will also need an allen wrench to take the initial two bolts out that anchors the grill bracket. Alternately you can just pry the front one off if you can't be bothered removing the grill, but beware as the emblem is screwed on so you woule never be able to use it again. Also you would still ahve to drill ut the screws that would be left. I thinks it's worth the extra effort to take the grill out. The front one went right into the same holes as the stock emblem. I'll post some pics of the finished job soon Last edited by boltuprite; 05-12-2008 at 09:08 AM.

Thread Tools
Show Printable Version Email this Page
Display Modes
Linear Mode Switch to Hybrid Mode Switch to Threaded Mode

Similar Threads
Thread	Thread Starter	Forum	Replies	Last Post
Need Help with JDM Emblems	Arganon	Inside and Out	14	01-10-2008 05:41 PM
jdm emblems	mrxkpex	Introduction & Pictures	4	07-05-2007 02:57 AM
JDM emblems	0oE	Inside and Out	23	03-31-2007 11:46 PM

05-09-2008, 12:42 PM	#2 (permalink)
tsltd Senior Member Join Date: Apr 2008 Location: Bay Area, CA Posts: 1,249 Hang	no you need to take them off look for the DIY exterior mods

05-09-2008, 12:49 PM	#3 (permalink)
k20z3 Koop Senior Member Join Date: Aug 2007 Location: Mass Posts: 1,808 Keith	http://www.grafixpressions.com/overlay_install.shtml

05-09-2008, 12:51 PM	#4 (permalink)
pgFA Senior Member Join Date: Oct 2007 Location: San Diego/Chula Vista, CA Posts: 81,605 Pogi	This one is for FA5 but I think its pretty similar. DIY '07 Si 4DR JDM/red badges

05-12-2008, 01:40 AM	#5 (permalink)
fhound258 Senior Member Member Join Date: Feb 2006 Posts: 577	thanks for that dyi, i got a 2dr but got the idea. see i got the overlays thinking they go over our stock ones but then realized that u need the orginal jdm emblems, so im just going to get those, btw if any one wants those overlays ill sell them dirt cheap.

08-05-2008, 10:44 PM	#7 (permalink)
zackster Junior Member Join Date: Jul 2008 Posts: 2	good looking you just asnwered my question i beenloking for for awhilee....

Remove Advertisements Sponsored Links
8th Generation Honda Civic Forum Advertisement