JDM Type R valve cover installed...

***blue rocket*** · 03-24-2007, 07:38 PM

Ok, first i'm going to touch on a few things, since i searched and searched before i bought my valve cover....but never found an answer to:

1 - There are no issues with putting the JDM Type R Valve cover on, except...there are no holes for the wires and such to the right of the valve cover...this honestly is no issue...i used a zip tie and a little rubber tape to make sure it sat securely and didnt rub against the valve cover.

2 - The breather tube on the JDM valve cover is wider than stock, you cannot reuse the stock clamp, but the hose will fit over it.

3 - I had a pain in the ass time getting the longer screws out on the stock spark plug cover...i ended up intentionally breaking the stock spark plug cover to get the bolts out so i could then get the nuts off - if you replace the spark plug cover you'll know what i'm talking about! The pic below shows what screws i'm talking about!

Other than that...i bought a new valve cover gasket, didnt use any type of sealant, it's not neccessary. Take your time removing the plastic shroud around the windshield wipers...it's not difficult to remove, but if you force it off you can break things. Total time of installation ~1.5 hours.

Here are a few pics!

Oohhh, thanks fedex!

Mmmm, JDM newspaper...

Before:

After:

Sorry for the bad lighting!

For anyone not sure how to remove the valve cover...it's pretty straight forward, thanks to BCJ fo the easy to follow write up!

DIY:Valve cover removal + gasket installation

***Ruthless909*** · 03-24-2007, 07:42 PM

Looks great mang!!

What's next??

KayGor · 03-24-2007, 07:45 PM

lolz.....sorry bro, but those are chinese newspaper!

***blue rocket*** · 03-24-2007, 08:06 PM

next is HFP body kit along with Volks TE37 Time attacks and jdm badges (just waitin for warmer weather)... retrofit, suspension and some other mods are already done! :)

***Ruthless909*** · 03-24-2007, 08:13 PM

**Nomar06** · 03-24-2007, 10:47 PM

good stuff

TeamValorRacing · 03-25-2007, 10:23 PM

now get the black dipstick and take off the 2.0 cover and it will look MAD Tyeeet JDM y0'!!eleven!111!

TWK20si · 03-25-2007, 10:32 PM

***blue rocket*** · 03-26-2007, 08:31 AM

Quote:

Originally Posted by TeamValorRacing

now get the black dipstick and take off the 2.0 cover and it will look MAD Tyeeet JDM y0'!!eleven!111!

The black dipstick reads inaccurately...so that's a big no for that. I think it looks to messy without the cover...so that's gonna stay too!

Tom1222 · 03-26-2007, 08:51 AM

Very Nice Pete

honda06si · 03-28-2007, 10:36 AM

looks good man...ive been wanting this mod for a long time...

ddldave · 05-21-2007, 11:40 PM

where can you get the red ones?

SI_ckness · 06-09-2007, 01:25 AM

thats nice . it looks so much better

inyong1988 · 06-09-2007, 01:29 AM

nice chinese newpaper

inyong1988 · 06-09-2007, 01:29 AM

Quote:

Originally Posted by ddldave

where can you get the red ones?

http://www.jdmland.com

si_turbo · 07-10-2007, 04:46 PM

where a good place to buy the red valve cover?

Si4Life · 07-10-2007, 04:49 PM

i love the jdm cover, the only thing is its not fully displayed with our cars. wish it wasnt so tucked in. +1

NIGHTHAWKSI · 07-10-2007, 05:06 PM

Quote:

Originally Posted by si_turbo

where a good place to buy the red valve cover?

lol...did you happen to look at the post above yours?

drr86 · 07-10-2007, 05:49 PM

***Excalibur*** · 07-10-2007, 06:46 PM

That's one clean engine bay. Makes me miss the looks of the oem airbox.

03-24-2007, 07:38 PM	#1 (permalink)
*blue rocket* The Sticker Man Join Date: Aug 2006 Location: CT Posts: 2,912 GrafiXpressions.com iTrader: 89 / 100%	JDM Type R valve cover installed... Ok, first i'm going to touch on a few things, since i searched and searched before i bought my valve cover....but never found an answer to: 1 - There are no issues with putting the JDM Type R Valve cover on, except...there are no holes for the wires and such to the right of the valve cover...this honestly is no issue...i used a zip tie and a little rubber tape to make sure it sat securely and didnt rub against the valve cover. 2 - The breather tube on the JDM valve cover is wider than stock, you cannot reuse the stock clamp, but the hose will fit over it. 3 - I had a pain in the ass time getting the longer screws out on the stock spark plug cover...i ended up intentionally breaking the stock spark plug cover to get the bolts out so i could then get the nuts off - if you replace the spark plug cover you'll know what i'm talking about! The pic below shows what screws i'm talking about! Other than that...i bought a new valve cover gasket, didnt use any type of sealant, it's not neccessary. Take your time removing the plastic shroud around the windshield wipers...it's not difficult to remove, but if you force it off you can break things. Total time of installation ~1.5 hours. Here are a few pics! Oohhh, thanks fedex! Mmmm, JDM newspaper... Before: After: Sorry for the bad lighting! For anyone not sure how to remove the valve cover...it's pretty straight forward, thanks to BCJ fo the easy to follow write up! DIY:Valve cover removal + gasket installation

03-24-2007, 10:47 PM	#6 (permalink)
Nomar06 mmm...what a tasty burger Join Date: Jul 2006 Location: Charlotte, NC Age: 27 Posts: 21,184 iTrader: 4 / 100%	good stuff __________________

LinkBacks (?) LinkBack to this Thread: http://www.8thcivic.com/forums/engine/33483-jdm-type-r-valve-cover-installed.html
Posted By	For	Type	Date
8th Generation Honda Civic Forum	This thread	Refback	02-04-2008 12:23 AM

Thread Tools
Show Printable Version Email this Page
Display Modes
Linear Mode Switch to Hybrid Mode Switch to Threaded Mode

Similar Threads
Thread	Thread Starter	Forum	Replies	Last Post
Official pics of the new Type R	FujiBlueSi	Garage	22	03-03-2007 08:48 PM
Will a K20A Type R Red Valve Cover fit on our K20Z3?	BubzSI	Bolt-Ons And All-Motor	3	02-07-2007 06:03 PM
Type R Valve Cover (will it fit?)	vtec_marine	Inside and Out	8	11-28-2006 09:59 AM
Installed my RED Valve Cover! :)	whitecivicsi	Introduction & Pictures	41	08-24-2006 04:24 PM
JDM Valve Cover	k-series	Do It Yourself Articles	21	08-04-2006 09:02 PM

03-24-2007, 07:42 PM	#2 (permalink)
*Ruthless909* Ahhh! Domokun! Join Date: Aug 2006 Location: +Evil Empire+ So.Cal (951) Age: 23 Posts: 7,118 4dr WhOrE!!! iTrader: 2 / 100%	Looks great mang!! What's next??

03-24-2007, 07:45 PM	#3 (permalink)
KayGor Member Join Date: Jan 2006 Location: Markham, Canada Posts: 78 iTrader: 1 / 100%	lolz.....sorry bro, but those are chinese newspaper!

03-24-2007, 08:06 PM	#4 (permalink)
*blue rocket* The Sticker Man Join Date: Aug 2006 Location: CT Posts: 2,912 GrafiXpressions.com iTrader: 89 / 100%	next is HFP body kit along with Volks TE37 Time attacks and jdm badges (just waitin for warmer weather)... retrofit, suspension and some other mods are already done! :)

03-24-2007, 08:13 PM	#5 (permalink)
*Ruthless909* Ahhh! Domokun! Join Date: Aug 2006 Location: +Evil Empire+ So.Cal (951) Age: 23 Posts: 7,118 4dr WhOrE!!! iTrader: 2 / 100%

03-25-2007, 10:23 PM	#7 (permalink)
TeamValorRacing Senior Member Join Date: Feb 2007 Posts: 1,005 iTrader: 6 / 100%	now get the black dipstick and take off the 2.0 cover and it will look MAD Tyeeet JDM y0'!!eleven!111!

03-25-2007, 10:32 PM	#8 (permalink)
TWK20si Senior Member Join Date: Jan 2007 Location: OH Age: 24 Posts: 749 Kevin iTrader: 8 / 100%

03-26-2007, 08:51 AM	#10 (permalink)
Tom1222 Senior Member Join Date: Jul 2006 Location: Indianapolis, Indiana USA Posts: 3,125 Tom Smith iTrader: 6 / 100%	Very Nice Pete

03-28-2007, 10:36 AM	#11 (permalink)
honda06si Senior Member Join Date: Sep 2006 Location: WV Posts: 11,158 justin iTrader: 6 / 100%	looks good man...ive been wanting this mod for a long time...

05-21-2007, 11:40 PM	#12 (permalink)
ddldave Member Join Date: May 2007 Age: 18 Posts: 91 Dave iTrader: 0 / 0%	where can you get the red ones?

06-09-2007, 01:25 AM	#13 (permalink)
SI_ckness Senior Member Join Date: May 2007 Location: tacoma wa Posts: 124 Eric iTrader: 0 / 0%	thats nice . it looks so much better

06-09-2007, 01:29 AM	#14 (permalink)
inyong1988 Senior Member Join Date: Jun 2006 Location: VIRGINIA Posts: 17,371 Junction Produce iTrader: 34 / 97%	nice chinese newpaper

07-10-2007, 04:46 PM	#16 (permalink)
si_turbo Senior Member Join Date: Sep 2006 Location: 909/626 Posts: 1,521 Justin iTrader: 1 / 100%	where a good place to buy the red valve cover?

07-10-2007, 04:49 PM	#17 (permalink)
Si4Life Senior Member Join Date: Feb 2007 Location: Hopewell Junction Posts: 2,131 Whos High Pitch? iTrader: 0 / 0%	i love the jdm cover, the only thing is its not fully displayed with our cars. wish it wasnt so tucked in. +1

07-10-2007, 05:49 PM	#19 (permalink)
drr86 Senior Member Join Date: Mar 2007 Location: Middleton, WI Age: 22 Posts: 150 Dan Reno iTrader: 0 / 0%

07-10-2007, 06:46 PM	#20 (permalink)
*Excalibur* VIP Member Join Date: May 2007 Location: Converse, TX. Age: 25 Posts: 7,580 Jeremy iTrader: 22 / 100%	That's one clean engine bay. Makes me miss the looks of the oem airbox.