![]() |
|
|
|
#1 (permalink) |
|
Member
|
Proof of Hp gain (Dyno) (SRI vs CAI)
I will try and make this brief. I had a Ingen CAI on my car for awhile. Then I saw all the hype about the X intake and it made me wonder if I could get better gains from this intake. So I sold my Ingen and I made my own custom SRI with the maf mod and have been driving the car with this intake for about a month now. I thought the car felt better and had better throttle response and was happy. So I went and had the car dynoed because I was wondering what kind of HP I had. So then I had a friend give me his AEM CAI and I decided to put it on and could instantly tell the gain in midrange power so now I wanted to take it back to the dyno and see what I gained. Here are the results. As you can see I picked up 15 hp and tq at the wheels in the midrange. Sorry I did not get a A/F reading with the CAI dyno pulls. My mods consist of custom race header, magnaflow exhaust, Hondata reflash, and the CAI.
Tim Last edited by xcellr8n; 05-14-2008 at 10:45 PM. |
|
|
|
|
|
#8 (permalink) |
|
Senior Member
|
Wah? You sold the Injen CAI (which probably makes more power than any other intake) to build your own intake (which if not sanded down properly will probably make only as much power as a stock housing)? Why didn't you just keep the Injen CAI in the first place?
|
|
|
|
|
|
#12 (permalink) |
|
Senior Member
|
Green = homemade Sri.
As stated above, if not made properly it will suck. I'm not sayin your homemade intake sucks but let's just say a homemade Sri will be suspect to more scrutiny/doubt than one such as X's. So the AEM made 15 hp over the homemade Sri? Could say a lot about the Sri. T. |
|
|
|
|
|
#15 (permalink) | |
|
Member
|
Quote:
|
|
|
|
|
|
|
#16 (permalink) |
|
Senior Member
|
Can you take a pic of the vanes on your DIY intake? Dynos are kinda irrelevant without that.
Also, the biggest benefit of the x-intake design is to richen up the AFR, so AFR on CAI would have been good. I know it's a stupid question to ask, but you used the same air filter (just different piping) on each of these runs, right? Last edited by Grizam303; 05-15-2008 at 05:47 PM. |
|
|
|
|
|
#18 (permalink) | |
|
Senior Member
|
Quote:
nice #s excellr8n |
|
|
|
|
|
|
#20 (permalink) |
|
Senior Member
|
If you followed the x-intake threads at all you know he put a lot of time & effort int R&D. Hence the reason he got so much support & so many orderes he couldn't fulfill them all (I am in no way defending the situation as it is now). Yes his intake was home-made, no i don't think that if xceller8n started slanging his home-made intakes over 8th he'd get the same response x's did.
There's not even a before & after dyno w/the homemade intake. (not that dyno's >all). Like I said, not disrespecting your intake xceller8n, just not enough information to make a judgement imho. T. |
|
|
|
![]() |
| Thread Tools | |
| Display Modes | |
|
|
Similar Threads
|
||||
| Thread | Thread Starter | Forum | Replies | Last Post |
| NX vs. ZEX 75 Wet Shot Dyno Proof NX MADE 235.8 FtLb@ 3900-4500 RPM! | blacksi2007 | Forced Induction And Nitrous | 10 | 04-06-2008 01:59 AM |
| Proof of HP gains with TB Spacer | alexv305 | Bolt-Ons And All-Motor | 91 | 08-10-2007 11:57 PM |
| Weapon R Intake Dyno: 14 hp gain | aki | Bolt-Ons And All-Motor | 43 | 02-02-2007 03:31 PM |
| How much HP gain from CAI And catback | Gaspar_06_Civic_EX | Bolt-Ons And All-Motor | 9 | 07-05-2006 08:03 PM |