torque specs?

beans · 07-04-2007, 12:08 AM

this is a simple but necessary question: what are the torque specs for the five bolts for the exhaust manifold? I've installed the header but need the torque numbers, thanks for the help.

***Sirbelch*** · 07-04-2007, 12:13 AM

tighten em until they glow.

jeremy0203 · 07-04-2007, 12:30 AM

ill tell you when i get my helms ina couple days =)

Kidekat · 07-04-2007, 12:32 AM

I would guess around 35 ftlbs if that... don't forget to recheck it after a few heat cycles.

televascular · 07-04-2007, 12:40 AM

"Install the exhaust manifold and tighten the bolts and nuts in a crisscross pattern in two or three steps, beginning with the inner bolt.

Torque Spec: 44 N/m (4.5 kgf/m, 33 lbf/ft)"

From what I can see in the Helms, there's at least one self-locking nut. Remember to always use brand new ones when reinstalling a part!

07-04-2007, 12:08 AM	#1 (permalink)
beans Member Join Date: Sep 2006 Location: The City Posts: 74 Vince iTrader: 0 / 0%	torque specs? this is a simple but necessary question: what are the torque specs for the five bolts for the exhaust manifold? I've installed the header but need the torque numbers, thanks for the help.

Thread Tools
Show Printable Version Email this Page
Display Modes
Linear Mode Switch to Hybrid Mode Switch to Threaded Mode

Similar Threads
Thread	Thread Starter	Forum	Replies	Last Post
I need torque Specs Please...	FG2z_K	Do It Yourself Articles	2	06-22-2007 11:53 PM
torque specs on lower and front bars by megan racing.	boostd7	Suspension and Brakes	1	04-18-2007 09:58 AM
torque specs for drain and fill bolt	SiLvErLIgHT06	Civic Coupe And Sedan	0	03-23-2007 10:39 AM
Lug nut torque specs	DigitalAnalog	Suspension and Brakes	3	09-08-2006 11:53 AM
torque specs ???	BLU BY U	Suspension and Brakes	4	07-15-2006 03:21 PM

07-04-2007, 12:13 AM	#2 (permalink)
*Sirbelch* Louder than 4 F404-GE-400 Join Date: Jan 2007 Location: Vacaville CA Age: 27 Posts: 6,498 Paul iTrader: 0 / 50%	tighten em until they glow.

07-04-2007, 12:30 AM	#3 (permalink)
jeremy0203 Senior Member Member Join Date: Jun 2007 Location: Saint Marys, GA Age: 23 Posts: 2,414 Jeremy iTrader: 6 / 100%	ill tell you when i get my helms ina couple days =)

07-04-2007, 12:32 AM	#4 (permalink)
Kidekat Senior Member Join Date: Jan 2007 Location: Placentia, CA Posts: 773 iTrader: 0 / 0%	I would guess around 35 ftlbs if that... don't forget to recheck it after a few heat cycles.

07-04-2007, 12:40 AM	#5 (permalink)
televascular Senior Member Join Date: Apr 2006 Location: New Jersey Posts: 291 iTrader: 0 / 0%	"Install the exhaust manifold and tighten the bolts and nuts in a crisscross pattern in two or three steps, beginning with the inner bolt. Torque Spec: 44 N/m (4.5 kgf/m, 33 lbf/ft)" From what I can see in the Helms, there's at least one self-locking nut. Remember to always use brand new ones when reinstalling a part!